MEM07019 - Program NC and CNC machining centre

Unit code:MEM07019Study level:TAFE

Nominal hours

20

Location

Sunshine

Prerequisites

MEM07015 - Set computer controlled machines and processes; and
MEM07016 - Set and edit computer controlled machines and processes; and
MEM07018 - Write basic NC and CNC programs; and
MEM09002 - Interpret technical drawing; and
MEM11011 - Undertake manual handling; and
MEM12023 - Perform engineering measurements; and
MEM12024 - Perform computations; and
MEM13015 - Work safely and effectively in manufacturing and engineering; and
MEM14006 - Plan work activities; and
MEM16006 - Organise and communicate information; and
MEM18001 - Use hand tools; and
MEM07005 - Perform general machining; or
MEM07028 - Operate computer controlled machines and processes
(Or equivalent to be determined by unit coordinator)
Co-requisites
(Corequisite units must be studied concurrently with this unit)

Overview

This unit of competency defines the skills and knowledge required to write and trial programs for numerically controlled (NC) and computer numerically controlled (CNC) machining centres.



The program may use common M and G codes and includes the programming of advanced operations, using canned cycles and sub-routines. Programs are trialled and edited as necessary to adjust operation of centre. Technical difficulties are resolved in consultation with appropriate technical advisers.


Where the selection and use of power tools/hand held operations is required unit MEM18002 Use power tools/hand held operations should also be selected.

Assessment

For Melbourne campuses

Assessment tasks will be designed to reinforce & extend knowledge and skill competence within set & controlled parameters in accordance with each unit’s learning outcomes & performance criteria requirements, including the setting of work based practical application tasks designed to provide evidence of competence outcomes, within periodic and scheduled timelines.
Students will be expected to demonstrate the following required skills:
Evidence required to demonstrate competence in this unit must be relevant to and satisfy the requirements of the elements and performance criteria on at least two (2) occasions and include:
• following work instructions, standard operating procedures (SOPs) and safe work practices
• identifying and interpreting specifications, charts, lists, drawings and other applicable reference documents in programming numerically controlled (NC) and computer numerically controlled (CNC) machining centres
• calculating coordinates for tooling and producing operation sheets for the program and process
• writing NC/CNC program in standard code format and incorporating, where appropriate, canned cycles and sub-routines
• producing NC/CNC operation sheets in accordance with SOPs
• operating the machine centre to test it operates to specification including undertaking any required editing of the program
• checking components or products for conformance to specifications.

Students will also be expected to demonstrate the following knowledge:
Evidence required to demonstrate the required knowledge for this unit must be relevant to and satisfy the requirements of the elements and performance criteria and include knowledge of:
• safe work practices and procedures and use of personal protective equipment (PPE)
• elements of NC and CNC program and the function of elements in controlling the operation of NC and CNC machines
• machining operations to be performed in the manufacture of the given part or product
• appropriate types of NC and CNC machines to perform the required machining operations
• machining operations to be controlled by the program to be written
• tool paths to be followed when producing the part or product and the sequence and reasons for selecting the sequence of machining operations to be programmed
• zero point of the NC and CNC machine
• canned cycles and sub-routines accessible in a particular NC and CNC machine and the application of each canned cycle and sub-routine available
• canned cycles and/or sub-routines to be used in the NC and CNC program and reasons for selecting the chosen canned cycles and/or sub-routines
• standard codes and their application used in the writing of NC and CNC programs
• procedures for writing NC and CNC programs in standard code format
• procedures for completing NC and CNC operation sheets and information to be included
• relevant Australian Standards for programming of NC and CNC machine centres
• procedures for manual operation of the NC and CNC machine
• reasons for testing and proving the NC and CNC program
• procedures for editing the NC and CNC program via the machine controller and the effects of editing on the operation of the NC and CNC machine and the part or product to be produced
• specifications of the part or product and measuring equipment/techniques to be used to check for conformance with specifications.

Required reading

The qualified trainer and assessor will provide teaching and learning materials as required in the form of workbooks produced by the Victoria University and/or via the Victoria University e-learning system.

As part of a course

This unit is studied as part of the following course(s):

Search for units, majors & minors